EXTERIOR
  • INTERIOR
  • PROTECTION
  • EQUIPMENT& ACCESSORIES
  • SHOP BY BRAND
  • Bilt Hamber Touch-Less V2 Pre-Wash

    Size

    Bilt Hamber Touch-Less – High-Performance Non-Contact Pre-Wash Snow Foam

    Bilt Hamber Touch-Less is a powerful alkaline snow foam designed to safely break down and remove traffic film, road grime, and contaminants before your contact wash. Engineered for use as a non-contact pre-wash, it’s the ideal first step in a swirl-free washing process, reducing the risk of inflicting scratches on your vehicle’s surface.

    Developed with biodegradable surfactants and advanced cleaning agents, Touch-Less lifts heavy dirt without compromising waxes or sealants. It clings well to vertical surfaces, allowing longer dwell times for maximum cleaning efficiency. Perfect for use with foam cannons and pressure washers, this is a must-have for any car enthusiast or detailer focused on safe, effective exterior cleaning.

    Features

    • Non-Contact Cleaning: Safely removes grime and traffic film before hand washing.
    • Highly Effective: Strong alkaline ph12 formulation breaks down stubborn dirt with ease.
    • Safe on Sealants: Will not degrade previously applied waxes, coatings, or sealants.
    • High Cling Formula: Foams well and adheres to surfaces for extended dwell time.
    • Pressure Washer Friendly: Designed for use in foam lances and cannons.
    • Biodegradable & Eco-Friendly: Contains environmentally responsible surfactants.

    Complete your safe wash routine with additional tools from our Detailing Tools and Accessories collection. Explore more from the Bilt Hamber range for pro-level car care.

    • Touch-Less may be applied with trigger spray, pump spray, pressure washer, or snow foam lance. The minimum recommended dilution rate should be 2% PIR (Panel Impact Ratio) and up to 5% for very dirty vehicles. Where application is through trigger spray or pump spray, the dilution calculation is easy to achieve, however, for application with pressure equipment it is essential to determine the amount of water being delivered to the equipment reservoir.
    • Fill the detergent bottle or reservoir (on machine or lance) up to capacity with plain water. Turn detergent feed to full. Take a large bucket or container and discharge the lance into this, watching the detergent bottle until empty. Once empty, stop.
    • The following calculations will achieve 4% dilution; Measure the total amount collected and multiply this number by 0.04 (Total can be measured in either volume with a measuring jug or by weight) this is the amount of Touch-Less to use.
    • Add the calculated amount from to the pressure-washer reservoir and top up to full with cold water and shake in for a few moments.
    • Apply touchless to entire vehicle or panel by panel. Allow to soak for 1-5 minutes (but never allow to dry). Power-wash off.
    • It is not necessary to use all diluted touch-less in one wash. One litre of diluted product should last 4-5 washes. Apply to cool panels in shaded conditions. Do not allow this product to dry in use. Keep the bottle neck and lid clean.

    Customer Reviews

    Based on 6 reviews
    83%
    (5)
    0%
    (0)
    17%
    (1)
    0%
    (0)
    0%
    (0)
    E
    Eugene
    Game Changer

    Not recommended for use with a foam cannon as you'll be wasting product unnecessarily. Works best with a battery powered sprayer. The difference between 2% and 1% dilution with V2 is minute – I've found multiple rounds at 1% dilution works better if you have some really stubborn dirt. Little to no dwell time required but needs a pressure washer.

    I
    ILYAS O.
    Need to use at 2% PIR to work

    I first used it at 1% PIR. There was zero difference between the panel with the product vs the panel that I used just water on. Tried the test again, this time at 2% PIR, and it worked a treat. However, 2% PIR from a foam cannon means you're using a lot of product; roughly 300ml of product in a 1litre cannon (3:7 ratio). That's a lot more than the usual 1:9 ratio that I use for other products. As a result, I'm not sure how I feel about the product overall.

    Z
    Zafer
    Absolutely Touchless

    Achieved amazing results with ungraded and long time unwashed car. Highly recommended.

    c
    corey g.
    Best dirt and grime remover

    This is best snow foam I have ever used it get 95 percent of the dirt and grime off your car

    M
    Muhammasd M.

    Bilt Hamber Touch-Less Pre-Wash 5L

    Bilt Hamber Touch-Less – High-Performance Non-Contact Pre-Wash Snow Foam

    Bilt Hamber Touch-Less is a powerful alkaline snow foam designed to safely break down and remove traffic film, road grime, and contaminants before your contact wash. Engineered for use as a non-contact pre-wash, it’s the ideal first step in a swirl-free washing process, reducing the risk of inflicting scratches on your vehicle’s surface.

    Developed with biodegradable surfactants and advanced cleaning agents, Touch-Less lifts heavy dirt without compromising waxes or sealants. It clings well to vertical surfaces, allowing longer dwell times for maximum cleaning efficiency. Perfect for use with foam cannons and pressure washers, this is a must-have for any car enthusiast or detailer focused on safe, effective exterior cleaning.

    Features

    • Non-Contact Cleaning: Safely removes grime and traffic film before hand washing.
    • Highly Effective: Strong alkaline ph12 formulation breaks down stubborn dirt with ease.
    • Safe on Sealants: Will not degrade previously applied waxes, coatings, or sealants.
    • High Cling Formula: Foams well and adheres to surfaces for extended dwell time.
    • Pressure Washer Friendly: Designed for use in foam lances and cannons.
    • Biodegradable & Eco-Friendly: Contains environmentally responsible surfactants.

    Complete your safe wash routine with additional tools from our Detailing Tools and Accessories collection. Explore more from the Bilt Hamber range for pro-level car care.

    Directions
    • Touch-Less may be applied with trigger spray, pump spray, pressure washer, or snow foam lance. The minimum recommended dilution rate should be 2% PIR (Panel Impact Ratio) and up to 5% for very dirty vehicles. Where application is through trigger spray or pump spray, the dilution calculation is easy to achieve, however, for application with pressure equipment it is essential to determine the amount of water being delivered to the equipment reservoir.
    • Fill the detergent bottle or reservoir (on machine or lance) up to capacity with plain water. Turn detergent feed to full. Take a large bucket or container and discharge the lance into this, watching the detergent bottle until empty. Once empty, stop.
    • The following calculations will achieve 4% dilution; Measure the total amount collected and multiply this number by 0.04 (Total can be measured in either volume with a measuring jug or by weight) this is the amount of Touch-Less to use.
    • Add the calculated amount from to the pressure-washer reservoir and top up to full with cold water and shake in for a few moments.
    • Apply touchless to entire vehicle or panel by panel. Allow to soak for 1-5 minutes (but never allow to dry). Power-wash off.
    • It is not necessary to use all diluted touch-less in one wash. One litre of diluted product should last 4-5 washes. Apply to cool panels in shaded conditions. Do not allow this product to dry in use. Keep the bottle neck and lid clean.