EXTERIOR
  • INTERIOR
  • PROTECTION
  • EQUIPMENT& ACCESSORIES
  • SHOP BY BRAND
  • How to Apply Ethos Graphene Matrix PRO 3.0

    How to Apply Ethos Graphene Matrix PRO 3.0

    Prep, application, cure and aftercare, step by step.

    Ethos Graphene Matrix PRO 3.0 bottle
    10 yearsRated protection
    5,000Washes, internal testing
    1 to 3 minFlash time
    24 hrsKeep dry

    Ethos Graphene Matrix PRO 3.0 is rated for 10 years of protection and 5,000 washes in Ethos internal wash-cycle testing, provided it is maintained correctly. How well it bonds comes down to preparation and technique, so this guide follows the Ethos application process from start to finish, working one section at a time and inspecting as you go.

    Pro Tip: The most common cause of poor bonding is skipping the panel strip with Ethos Detox. Do not rush Step 4 of the prep.

    What You Need

    Graphene Matrix PRO 3.0 and applicator (shake well)
    Ethos Detox panel prep spray
    Clay mitt or clay bar
    At least 4 to 6 plush microfibre towels
    Polish, if needed to remove swirls first
    Spare applicators
    Nitrile gloves
    Flashlight or phone light

    Before You Start

    • Work out of direct sun on a cool panel, in a clean, dry space.
    • Aim for 18 to 24°C (65 to 75°F).
    • Heat and humidity shorten the flash window, so a hot garage is not suitable.
    • Do a small test section first to get a feel for the flash time.

    Prep the Paint

    1

    Wash and Dry

    Wash the vehicle, remove loose dust and dirt, then dry it completely.

    Wiping a panel with a microfibre towel during prep
    2

    Decontaminate with Clay

    Clay the paint with a clay mitt or bar. Rub the back of your hand over the paint inside a plastic bag. If it feels gritty, clay it again.

    3

    Correct with Polish

    Polish or compound out scratches, swirls and oxidation before coating. The coating seals in whatever is underneath it.

    4

    Strip with Ethos Detox

    Wipe every panel with Ethos Detox to remove polishing oils, waxes and residue. Skipping this step is the most common cause of bonding failure.

    5

    Purge Trapped Water

    Open and close the doors, bonnet and boot several times, then dry the panel gaps, mirrors, headlights and taillights.

    Apply the Coating

    1

    Shake and Glove Up

    Shake the bottle well and put on nitrile gloves.

    Gloved hand holding a microfibre applicator on black paint
    2

    Saturate the Applicator

    Saturate the suede face of the applicator until it is wet, not just damp. Ethos states you cannot over-apply PRO 3.0. Any excess buffs away.

    Loading the applicator with Ethos Graphene Matrix PRO 3.0
    3

    Cross-Hatch One Section

    Work one 2 ft x 2 ft section at a time (about 60 cm x 60 cm, roughly a door or half a bonnet). Go top to bottom, then side to side.

    Applying the coating to a bonnet with an applicator
    4

    Keep It Wet

    Reload when the applicator stops gliding. Add more product instead of more pressure.

    5

    Watch for the Flash

    Wait 1 to 3 minutes (up to 5 in cooler conditions). The coating is ready when it sweats and beads. Do not buff before the beads appear and do not wait long after.

    Freshly applied coating on a bonnet before levelling
    6

    Level and Buff

    Use a clean plush microfibre towel in small circles with almost no pressure. Flip to a clean side for a second pass to reach high gloss.

    Buffing a bonnet with a microfibre towel
    7

    Inspect with a Light

    Check the panel and its neighbours under a flashlight or phone light. Leftover residue cures into high spots that then need polishing out. Avoid pushing coating onto adjacent panels.

    8

    Repeat Across the Vehicle

    Continue section by section across paint, plastic trim and glass, including the windscreen.

    Ethos Graphene Matrix PRO 3.0 finish on a black bonnet

    Layering (Optional)

    • One coat gives full protection.
    • For another layer, wait at least 15 minutes after buffing.
    • Apply no more than 3 coats in 24 hours.

    Cure Time

    2 hrsBefore driving
    24 hrsBefore any water or rain
    7 daysBefore the first wash

    The coating keeps hardening for several days. A longer dry time helps.

    Aftercare Schedule

    How Often What to Do
    Every 1 to 2 weeks Hand wash with a pH-neutral, coating-safe shampoo such as Ethos Cleanse and a clean mitt. No brush car washes.
    Every 4 to 6 weeks Mist a compatible spray after washing, such as Ethos RESIST.
    Every 6 months Remove embedded iron and fallout with Ethos Iron & Fallout Remover.

    Ethos also offers a Ceramic Coating Maintenance Kit that bundles these products.

    Warranty Requirements

    • Register within 30 days of installation.
    • Provide your VIN, install date and proof of purchase.
    • Follow the maintenance schedule above, keep your receipts and complete the annual digital check-in.
    • No polishing and no brush car washes.
    • Ethos products are logged automatically against your registration.
    • Coverage transfers with the vehicle.

    Pro Tips

    • Test a small section to learn your timing for the day's conditions.
    • Plan your panels in advance and finish each one before moving on.
    • Check for residue with a flashlight before it cures.
    • Do not press harder to stretch the coating. Add more product.
    • Skip wax, which conflicts with the coating. Use RESIST instead.

    Do It Right. See the Difference.

    Frequently Asked Questions

    What if I spot a high spot or streak?

    If you catch it immediately, add a little coating to re-wet the area, wait for it to flash, then level it again. If it has already cured, polish with a finishing polish and re-coat.

    How much do I need?

    50mL covers trucks, SUVs and larger vehicles, or a sedan with multiple coats. 100mL covers multiple vehicles or maximum-build layering on one.

    Can I apply it in the sun or a hot garage?

    No. Heat makes the coating flash too fast, so avoid direct sun and hot garages.

    Which surfaces can I coat?

    Any painted, plastic or glass surface, including the windscreen.

    What if it gets wet before 24 hours?

    Keep the vehicle covered or indoors. If it does get wet, gently blot with a microfibre towel and do not rub.

    When can I wash it?

    Wait 7 days, then hand wash every 1 to 2 weeks with a coating-safe shampoo.

    Should I wax over it?

    Wax is not recommended. Use RESIST every 4 to 6 weeks instead.

    How long does it last?

    It is rated for 10 years and 5,000 washes in Ethos internal testing, with maintenance kept on schedule.

    When do I register the warranty?

    Within 30 days of installation, with your VIN, install date and proof of purchase.

    Shop Ethos at AutoBuff

    Browse the full Ethos range, including coatings and prep products, in our Ethos collection.